Toggle theme
User Tools
Toggle theme
Site Tools
Search
You are here:
Welcome to PlanetCNC.zone
»
G-Code
»
Operators
»
Not equal (ne)
Trace:
gcode:operators:oper-not_equal
Sitemap
This is a sitemap over all available pages ordered by
namespaces
.
expr
gcode
comments
functions
gcodes
G00 - Rapid Move
G01 - Linear Feed Move
G02 - Clockwise Arc Feed Move
G03 - Counter Clockwise Arc Feed Move
G04 - Dwell
G05.1 - Quadratic Spline
G05.2 - Cubic Spline
G05.3 - NURBS Block End
G05 - Cubic Spline
G06.1 - Shapes Clear
G06.2 - Shapes Load
G06.3 - Shapes Process
G06 - Shapes Exec
G07 - Lathe Mode – Diameter
G08 - Lathe Mode – Radius
G09 - Stop, Sync & Set Controller Position
G10 - Settings
G12 - Mill: Circular Pocket CW
G13 - Mill: Circular Pocket CCW
G15 - Polar Coordinate Cancel
G16 - Polar Coordinate Enable
G17 - XY Plane
G18 - ZX Plane
G19 - YZ Plane
G20 - Inch Units
G21 - Millimeter Units
G28.1 - Set Home 1 Position
G28 - Go To Home 1 Position
G30.1 - Set Home 2 Position
G30 - Go To Home 2 Position
G31 - Probe
G32 - Spindle Synchronized Motion / Threading
G33.1 - Spindle Synchronized Motion With Return / Rigid Tapping
G33 - Spindle Synchronized Motion / Threading
G38.1 - Probe
G38.2 - Probe
G38.3 - Probe
G38.4 - Probe
G38.5 - Probe
G40 - Tool Compensation Cancel
G41.1 - Tool Compensation Dynamic Left
G41 - Tool Compensation Left
G42.1 - Tool Compensation Dynamic Right
G42 - Tool Compensation Right
G43.1 - Tool Offset+ Enable
G43 - Tool Offset+ Enable
G44.1 - Tool Offset- Enable
G44 - Tool Offset- Enable
G49 - Tool Offset Cancel
G50 - Axes Scale Cancel
G51 - Axes Scale Enable
G52.1 - Axes Offset Cancel
G52.1 - Axes Offset
G53 - Machine Coordinate System
G54.1 - Coordinate System P
G54 - Coordinate System 1
G55 - Coordinate System 2
G56 - Coordinate System 3
G57 - Coordinate System 4
G58 - Coordinate System 5
G59.1 - Coordinate System 7
G59.2 - Coordinate System 8
G59.3 - Coordinate System 9
G59 - Coordinate System 6 or P
G61 - Blend Cancel
G64 - Blend Enable
G65 - Call Macro
G68 - Axes Rotate Enable
G69 - Axes Rotate Cancel
G70 - Inch Units
G70 - Millimeter Units
G72.1 - Mill: Profile
G72.2 - Mill: Pocket
G72 - Mill: Facing
G73 - Drill Cycle: Drill, Speed Peck, Dwell
G74 - Tap: Left
G76 - Turn: Threading
G80 - Cancel Motion
G81 - Drill Cycle: Drill
G82 - Drill Cycle: Drill, Dwell
G83 - Drill Cycle: Drill, Peck, Dwell
G84 - Tap: Right
G85 - Bore: Feed In, Feed Out
G86 - Bore: Feed In, Spindle Stop, Rapid Out, Spindle Start
G87 - Bore: Feed In, Spindle Reverse, Rapid Out, Spindle Reverse
G88 - Bore: Feed In, Spindle Stop, Feed Out, Spindle Start
G89 - Bore: Feed In, Spindle Reverse, Feed Out, Spindle Reverse
G90.1 - Distance Mode – IJK Absolute
G90.2 - Distance Mode – ABC Absolute
G90 - Distance Mode – Absolute
G91.1 - Distance Mode – IJK Incremental
G91.2 - Distance Mode – ABC Incremental
G91 - Distance Mode – Incremental
G92.1 - Working Offset Set
G92 - Working Offset
G93 - Feed Mode - Inverse Time
G94 - Feed Mode - Units per Minute
G95 - Feed Mode - Units per Revolution
G96 - Spindle Mode – CSS
G97 - Spindle Mode – RPM
G98 - Cycle Return - Initial Z Point
G99 - Cycle Return - R Point
G-Codes
toc_gcodes1
toc_gcodes2
toc
macros
mcodes
operators
other
owords
About
G-Code
Order of execution
toc
hardware
kb
playground
sdk
solutions
tng
wiki
Welcome to PlanetCNC.zone
toc_expr
toc_gcode
toc_hardware
toc_kb
toc_sdk
toc_solutions
toc_tng
toc
gcode/operators/oper-not_equal.txt
· Last modified:
2023/01/20 11:25
by
127.0.0.1
Page Tools
Show page
Back to top
