Sidebar

Home



PlanetCNC TNG


Introduction
Overview
Installation


User Interface


Main Window

File Menu

View Menu

Program Menu

Machine Menu

  Emergency Stop
  Start
  Stop
  Pause
  Start Options
  Overrides
   Speed Override
   Spindle Override
   Pause Enable
   Pause Optional
   Single Step
  Mist
  Flood
  Spindle
  Output
  ExtOut
  Motor, Limits, Probe
   Motors Enable
   Soft Limits Enable
   Hard Limits Enable
   Probe Trigger
  Tools
   Current
   Change
   Select
   Edit Tool Table
   Edit Tool Slots
   Measure Current Tool
   Measure All Tools
  Move
   To Zero
   To...
   Axis To Zero
   To G28, G30
   To Selected Line
   To Mark
   Program Bounds
   Position To Camera
   Camera To Position
   Camera To Sel. Line XY
  Machine Position
   To Zero
   To...
   Axis To Zero
   Unwind
   Measure Height
   As G28, G30
   Reset THC
  Work Position
   To Zero
   To...
   Axis To Zero
   From Program
   Measure Height
   Offset To Zero
   Offset To...
   Offset Axis To Zero
   Selected Line
   Camera
  Coordinate System
   Current
   Select
   To Zero
   To...
   Axis To Zero
   Measure Height
   Offset To Zero
   Offset To...
   Offset Axis To Zero
   Edit Coordinate Systems
  Tool Offset
   Enabled
   To Zero
   To...
   Axis To Zero
   Measure Length
   From Tool Table
  Home
  Cycle
   Mill Facing
   Mill Profile
   Mill Pocket
   Mill Circular Pocket
   Drill
   Drill Tap
   Turn Facing
   Turn Roughing
   Turn Repeating
   Turn Finishing
   Turn Grooving
   Turn Threading
  Measure
   Probe Calibration
   Edge Find
   Edge Position
   Edge Angle
   Inside Corner
   Outside Corner
   Hole
   Protrusion
   Slot
   Tab
   Surface Height
   Surface Angle
   Surface
   Gantry Square
  Points
   Count
   Load
   Save
   Save STL
   Save DXF
   To Output
   Clear
   Add From Position
   Add From Camera
  Camera
   Show
   Mark
   Read
   Calibrate Scale
   Set Offset
  User Commands
  Controller
   Reconnect
   Reset
   Firmware Update
   Advanced

Help Menu


Settings



Parameters


tng:machine_menu:machine_menu-overrides_speed_override

Speed Override

Speed Override Enable

Enables traverse and feed speed override options. When this item is disabled (no check), override controls trough either Override menu or Speed segment will have no affect on speed values.

If speed override is disabled, the speed icon is using red color.

If speed override is used, the speed icon is using orange color.

Otherwise speed icon color is normal.

Traverse

Overrides speed setting for traverse speed. Default traverse speed value is set in settings: File/Setting/Program Defaults/Traverse Speed.

Speed override controls are available also in speed panel on main window.

Current

Shows current traverse speed override value.
100% means there is no traverse speed override used.

Reset

Resets any traverse speed override.

Increase

Increases traverse speed override setting for 10%.

Decrease

Decreases traverse speed override setting for 10%.

Feed

Overrides speed setting for feed speed. Feed speed setting is set in in G-code program with F-word or in settings: File/Setting/Program Defaults/Feed Speed.

Speed override controls are available also in speed panel on main window.

Current

Shows current feed speed override value.
100% means there is no feed speed override used.

Reset

Resets any feed speed override.

Increase

Increases feed speed override setting for 10%.

Decrease

Decreases feed speed override setting for 10%.

tng/machine_menu/machine_menu-overrides_speed_override.txt · Last modified: 2023/01/27 13:10 by 127.0.0.1

Page Tools